New Products
Rammable Refractory 5 Kg Repair Pack
5kg Repair Pack Volume as below but divided by 5.
Supplied in sealed plastic bag not a box as per photo…
Ramming Dolly Moulders Hardwood Rammer
Hardwood Rammer (Ramming Dolly Used by Foundry Moulders) The ramming dolly is an essential tool for ramming sand into the moulding…
Refractory Paint Crisolflow N - ladles, skimmers 1Kg Tin
Crisolflow N (1kg Tin)
This is a special coating for casting tools with good mechanical properties, i. e. it protects the…
Refractory Paint for ladles, tools ingot moulds 100g tub
Description: Refractory paint is a soft grease, containing refractory pigments and is designed for painting onto ladles or other surfaces in…
Replace Furnace Base bricks
Replacement Bricks in LPG Furnace base only IF lid needs repair this is a separate cost. (Photograph shows a new furnace) The following…
Replace Furnace Lid bricks
Replacement Bricks in LPG Furnace LID only (Photograph shows a new furnace) The following restorative works will be undertaken to bring your furnace…
Roll Pin 120 pcs set
Roll Pins (sometimes called Tension or Spring Pins) are mechanical fastener that secures the position of two or more parts of a machine relative…
Sand Delft Clay Moulding Box Casting Flask
Traditional Jewellers metal casting flask/moulding box robustly made from cast iron Traditional sand casting flask Vertical & horizontal filling Held securely by two…
Sand Scoop Round Plastic
Sand Scoop When filling the flask (drag and cope) this is a useful aid when completing work on the bench rather…
Shell Investment Lost Wax Casting (Course 4)
This course stands independently as an introduction to the craft of Lost Wax Casting using the Shell investment technique. Previous knowledge and…
Shrinkage Rule for Pattern Making 24" 13/32nds per foot
Used Stock to Clear SORRY SOLD OUT Patternmakers’ contraction allowances Castings are always smaller in dimensions than the pattern from which…
Silica Sand 60 Grit/ Mesh for Core Making
25Kg gross weight inclusive of packaging (This sand needs to be mixed with Sodium Silicate to be ready to use) Using Kiln…
Silicon Bronze Ingot 1kg
The temperature for pouring should be between 1150 degrees centigrade to 1180. Silicon Bronze Ingot for Bronze sculpture. (Ingot weights are…
Silicon Bronze Ingot 8.5kg
Silicon Bronze Ingot for Bronze sculpture.(Ingot weights are plus or minus 2.5% as all ingots are different sizes) This is…
Silicon Bronze Ingot 8.5kg
The temperature for pouring should be between 1150 degrees centigrade to 1180. Silicon Bronze Ingot for Bronze sculpture. (Ingot weights are…
Sodium Silicate 1 Litre For making core sand)
(Sufficient to make 30 to 50 Kgs of core moulding sand dependant upon the addition rate) Application - Measure the amount of dry sand by pouring it into…
Sodium Silicate 5 Litres For making core sand)
(Sufficient to make 150 to 250 Kgs of core moulding sand dependant upon the addition rate) Application - Measure the amount of dry sand by pouring it…
Sodium Silicate 500ml For making core sand)
(Sufficient to make 30 to 50 Kgs of core moulding sand dependant upon the addition rate) Application - Measure the amount of dry sand by pouring it into…
Sprue Cutter 25mm diameter 300mm long
We have had these 25mm by 300mm long sprue cutter specially made from thin wall polished stainless steel. Being so…
Steel Ladle 10cm Diameter with a 47cm handle
Heavy Duty Steel Ladle 10cm Diameter (4 inches Capacity 250ml approx) Handle length 45cm Total length 55cm The ladle has a pouring…